Buy Used Batch-Type Body-Only Reactors for Sale

Réacteurs agités de type discontinu d'occasion à vendre

Buying used batch-type body-only reactors through International Process Plants gives pharmaceutical, chemical processing, biotech, food and beverage, and cosmetics manufacturers access to bare jacketed pressure vessels delivered without an agitator drive, shaft, or impeller assembly from Pfaudler, DeDietrich, UGE, EHW Thale, and additional OEM manufacturers. ▶

Capacities span 15 L (4 gallons) shop-test bodies and 37.9 L (10 gallons) pilot vessels up to a 30,300 L (8,000 gallons) DeDietrich SA shell. Internal pressure ratings extend from 0.14 bar (2 psi) atmospheric service through 20.7 bar (300 psi) on a DeDietrich CTJ glass-lined vessel. Internal temperature envelopes reach 260 degrees C (500 degrees F) on the largest glass-lined Pfaudler and DeDietrich shells. Internal full vacuum capability is available across the inventory. Support configurations are split between leg-mounted and lug-mounted skirts depending on installation footprint.

Pfaudler bodies are stocked across the RA, RS, P, E, ELL, KC, and KA series. DeDietrich bodies span the SA, CTJ, CE, STU, and CSA series. Universal Glasteel Equipment (UGE) supplies factory-new bodies across the UA-300, UA-500, UA-1000, UA-2000, and UA-4000 ranges plus the Base UT-30, UT-50, UT-100, and UT-200 base series. Condition grades on offer cover re-glassed, good used, factory-new, needs-reglass, and unused-surplus stock. Jacket configurations include standard heat-transfer jackets and half-pipe (limpet) coil jackets. All vessels are offered as ASME-coded, National Board, CRN, CE-marked, or PED compliant where the original code stamp permits. Buying used batch-type body-only reactors from IPP can save up to 50% of capital and 90% of lead time versus buying new. ▲

150+

Réacteurs en stock

1980

Établi depuis

15

Pays ayant des bureaux

Re-Glassed Bodies

Pfaudler & DeDietrich shells

New Bodies from UGE

Factory-new glass-lined stock

All Body-Only Vessels

15 L to 30,300 L capacity range

Buy Used Batch-Type Body-Only Reactors for Sale by Manufacturer

IPP stocks batch-type body-only reactor vessels from a wide range of OEM brands, with Pfaudler and DeDietrich representing the deepest single-manufacturer positions in the inventory. Buying a body shell from the original equipment manufacturer simplifies retrofit drive sizing, replacement-glass scheduling, and code documentation continuity.

Buy Used Pfaudler Body-Only Reactors for Sale

Pfaudler is the deepest single-OEM position in IPP’s batch-type body-only inventory. Body shells are stocked across the RA, RS, P, E, ELL, KC, and KA series in re-glassed, used, unused, and needs-reglass conditions.

Pfaudler RS — 22,700 L

Re-glassed Pfaudler RS glass-lined reactor body. 22,700 L (6,000 gallons) capacity at 8.6 bar (125 psi) and 232.2 degrees C (450 degrees F).

Capacité (conception) : 22,700 L (6,000 gallons) capacity

Pression interne : 8,6 bar (125 psi)

Température interne : 232.2 degrees C (450 degrees F)

Matériel: Construction à revêtement de verre

Diamètre: 2 750 mm (108,3 pouces)

Longueur du côté droit : 3,300 mm (129.9 in) shell

Condition: État revitré

Type de support : leg-mounted

Pfaudler KC — 18,950 L

Unused Pfaudler KC glass-lined reactor body. 18,950 L (5,000 gallons) capacity rated to 6.2 bar (90 psi) and 204.4 degrees C (400 degrees F) with full vacuum capability.

Capacité (conception) :18,950 L (5,000 gallons) capacity

Pression interne :6.2 bar (90 psi)

Température interne :204.4 degrees C (400 degrees F)

Vide interne complet :Capacité de vide complète

Diamètre:2 750 mm (108,3 pouces)

Longueur du côté droit :4,550 mm (179.1 in) shell

Condition: État inutilisé

Type de support : leg-mounted

Pfaudler RS — 11,350 L

Used Pfaudler RS glass-lined reactor body. 11,350 L (3,000 gallons) capacity rated to 10.3 bar (150 psi) and 232.2 degrees C (450 degrees F).

Capacité (conception) :11,350 L (3,000 gallons) capacity

Pression interne :10,3 bar (150 psi)

Température interne :232.2 degrees C (450 degrees F)

Vide interne complet :Capacité de vide complète

Diamètre:2 450 mm (96,5 pouces)

Longueur du côté droit :1,850 mm (72.8 in) shell

Condition:État d'occasion

Type de support :lug-mounted

Buy Used DeDietrich Body-Only Reactors for Sale

DeDietrich is the second deepest OEM position in IPP’s batch-type body-only inventory. Body shells span the SA, CTJ, CE, STU, and CSA series across re-glassed and needs-reglass condition grades.

DeDietrich SA — 30,300 L

Needs-reglass DeDietrich SA glass-lined reactor body. 30,300 L (8,000 gallons) capacity rated to 6.9 bar (100 psi) and 260 degrees C (500 degrees F) — the largest body shell in IPP inventory.

Capacité (conception) :30,300 L (8,000 gallons) capacity

Pression interne :6,9 bar (100 psi)

Température interne :260 degrees C (500 degrees F)

Diamètre:3 050 mm (120,1 pouces)

Longueur du côté droit :3,650 mm (143.7 in) shell

Condition:Needs reglass condition

Type de support :Lug-mounted

DeDietrich SA — 3,800 L

Re-glassed DeDietrich SA glass-lined reactor body. 3,800 L (1,000 gallons) capacity rated to 6.9 bar (100 psi) and 260 degrees C (500 degrees F) with full vacuum capability.

Capacité (conception) :3,800 L (1,000 gallons) capacity

Pression interne :6,9 bar (100 psi)

Température interne :260 degrees C (500 degrees F)

Vide interne complet :Capacité de vide complète

Diamètre:1 600 mm (63 pouces)

Longueur du côté droit :1,850 mm (72.8 in) shell

Condition:revitruré

Type de support :leg-mounted

Nouveaux équipements — fabriqués sur mesure

DeDietrich CTJ — 189.3 L

Re-glassed DeDietrich CTJ glass-lined reactor body. 189.3 L (50 gallons) capacity rated to 20.7 bar (300 psi) — the highest internal pressure rating in IPP inventory.

Capacité (conception) :189.3 L (50 gallons) capacity

Pression interne :20.7 bar (300 psi) pressure rating

Température interne :204.4 degrees C (400 degrees F)

Diamètre:889 mm (35 in)

Longueur du côté droit :737 mm (29 in) shell

Condition:revitruré

Type de support :leg-mounted

Nouveaux équipements — fabriqués sur mesure

Buy Body-Only Reactors from Other Manufacturers

Beyond Pfaudler and DeDietrich, IPP stocks body-only reactor shells from Universal Glasteel Equipment (UGE), EHW Thale, Schwelm, Glasscote, Redicon, Portobello Fabrications, Balfour, and Lampart. UGE is an IPP subsidiary that supplies factory-new glass-lined bodies under the IPP umbrella.

UGE UA-1000 — 3,800 L

New UGE UA-1000 glass-lined reactor body. 3,800 L (1,000 gallons) capacity rated to 6.9 bar (100 psi) and 232.2 degrees C (450 degrees F) with factory-new glass lining.

Capacité (conception) :3,800 L (1,000 gallons) capacity

Pression interne :6,9 bar (100 psi)

Température interne :232.2 degrees C (450 degrees F)

Vide interne complet :Capacité de vide complète

Diamètre:1,500 mm (59.1 in)

Longueur du côté droit :2,250 mm (88.6 in) shell

Condition:État neuf

Type de support :leg-mounted

New equipment — in stock

EHW Thale — 5,700 L

Re-glassed EHW Thale glass-lined reactor body. 5,700 L (1,500 gallons) capacity rated to 6.9 bar (100 psi) and 232.2 degrees C (450 degrees F).

Capacité (conception) :5,700 L (1,500 gallons) capacity

Pression interne :6,9 bar (100 psi)

Température interne :232.2 degrees C (450 degrees F)

Diamètre:2 000 mm (78,7 pouces)

Longueur du côté droit :1,500 mm (59.1 in) shell

Condition:État revitré

Type de support :Leg-mounted

Portobello Fabrications — 14,950 L

Used Portobello Fabrications LTD. stainless steel 316L reactor body. 14,950 L (3,950 gallons) capacity rated to 6.2 bar (90.1 psi) and 200 degrees C (392 degrees F) — an alloy alternative to glass-lined construction.

Capacité (conception) :14,950 L (3,950 gallons) capacity

Pression interne :6.2 bar (90.1 psi)

Température interne :200 degrees C (392 degrees F)

Matériel:Acier inoxydable 316L

Diamètre:2,400 mm (94.5 in)

Longueur du côté droit :2,500 mm (98.4 in) shell

Condition:État d'occasion

Type de support :lug-mounted

Buy Used Batch-Type Body-Only Reactors for Sale by Condition

IPP stocks batch-type body-only reactor vessels in re-glassed, used, factory-new, needs-reglass, and unused-surplus condition grades. Choose the condition that matches your budget, timeline, and glass-lining requirements.

Buy Re-Glassed Reactor Bodies

IPP stocks re-glassed batch type body only reactor vessels. Re-glassing is performed by IPP’s UGE (Universal Glasteel Equipment) division, which stocks 700+ vessels and 2,700+ parts. Re-glassed reactor bodies receive new glass linings with full fire polish and very clean glass condition on existing OEM vessels. These vessels offer restored corrosion protection at significant savings compared to new OEM equipment.

DeDietrich SA — 3,800 L

Re-glassed DeDietrich SA glass-lined reactor body. 3,800 L (1,000 gal) capacity with full vacuum capability, full fire polish, and very clean glass condition.

Capacité (conception) :Capacité de 3 800 L (1 000 gal).

Pression interne :6,9 bar (100 psi)

Température interne :260 °C (500 °F)

Vide interne complet :Capacité de vide complète

Polissage du verre au feu :Full Fire Polish

État du verre :Very Clean glass

Diamètre:1 600 mm (63 pouces)

Longueur du côté droit :1,850 mm (72.8 in)

Type de support :Jambes

Pfaudler ELL — 1,900 L

Re-glassed Pfaudler ELL glass-lined reactor body. 1,900 L (500 gal) capacity with full vacuum, full fire polish, and very clean glass condition.

Capacité (conception) :Capacité de 1 900 L (500 gal).

Pression interne :6,9 bar (100 psi)

Température interne :176,7°C (350°F)

Vide interne complet :Capacité de vide complète

Polissage du verre au feu :Full Fire Polish

État du verre :Very Clean glass

Diamètre:1,500 mm (59.1 in)

Longueur du côté droit :914 mm (36 pouces)

Type de support :Jambes

Pfaudler RS — 7,550 L

Re-glassed Pfaudler RS glass-lined reactor body. 7,550 L (2,000 gal) capacity with full vacuum, full fire polish, and very clean glass condition.

Capacité (conception) :Capacité de 7 550 L (2 000 gal).

Pression interne :6,9 bar (100 psi)

Température interne :232,2 °C (450 °F)

Vide interne complet :Capacité de vide complète

Polissage du verre au feu :Full Fire Polish

État du verre :Very Clean glass

Diamètre:2 000 mm (78,7 pouces)

Longueur du côté droit :2,050 mm (80.7 in)

Type de support :Cosses

Buy Used Reactor Bodies for Sale

IPP stocks used batch type body only reactor vessels. Used reactor bodies are available from Pfaudler, DeDietrich, and other manufacturers. Used vessels retain existing glass linings with varying degrees of fire polish. Good used condition offers the lowest price point while providing OEM-quality vessel shells that can serve as replacement bodies or accept new agitation systems.

Pfaudler RS — 7,550 L

Used Pfaudler RS glass-lined reactor body. 7,550 L (2,000 gal) capacity with 10.3 bar (150 psi) pressure rating and full vacuum capability.

Capacité (conception) :Capacité de 7 550 L (2 000 gal).

Pression interne :10,3 bar (150 psi)

Température interne :232,2 °C (450 °F)

Vide interne complet :Capacité de vide complète

Polissage du verre au feu :Some Fire Polish

État du verre :Dirty (light cleaning)

Diamètre:2 000 mm (78,7 pouces)

Longueur du côté droit :2,050 mm (80.7 in)

Type de support :Cosses

Type de tête inférieure :Elliptical

Pfaudler RS — 11,350 L

Used Pfaudler RS glass-lined reactor body. 11,350 L (3,000 gal) capacity with 10.3 bar (150 psi) pressure rating and full vacuum capability.

Capacité (conception) :Capacité de 11 350 litres (3 000 gallons).

Pression interne :10,3 bar (150 psi)

Température interne :232,2 °C (450 °F)

Vide interne complet :Capacité de vide complète

Polissage du verre au feu :Some Fire Polish

État du verre :Clean glass

Diamètre:2 450 mm (96,5 pouces)

Longueur du côté droit :1,850 mm (72.8 in)

Type de support :Cosses

Type de tête inférieure :Elliptical

Pfaudler KA — 7,550 L

Used Pfaudler KA glass-lined reactor body. 7,550 L (2,000 gal) capacity with sanitary construction, full vacuum capability, and sanitary jacket shroud.

Capacité (conception) :Capacité de 7 550 L (2 000 gal).

Pression interne :6,9 bar (100 psi)

Température interne :232,2 °C (450 °F)

Vide interne complet :Vide complet

Construction sanitaire :sanitary construction

Sanitary Jacket Shroud:Sanitary jacket shroud

Diamètre:2 000 mm (78,7 pouces)

Longueur du côté droit :2 200 mm (86,6 po)

Type de support :Cosses

Buy New Reactor Bodies from UGE

IPP stocks new glass-lined reactor bodies from Universal Glasteel Equipment (UGE). UGE is IPP’s glass-lined equipment subsidiary, founded in 1995. New UGE reactor bodies ship with factory-new glass linings and immediate availability from stock. These vessels provide new-equipment glass quality without extended OEM lead times.

UGE UA-300 — 1,150 L

New UGE UA-300 glass-lined reactor body. 1,150 L (300 gal) capacity with full vacuum capability and factory-new glass lining.

Capacité (conception) :Capacité de 1 150 L (300 gal).

Pression interne :6,9 bar (100 psi)

Température interne :232,2 °C (450 °F)

Vide interne complet :Capacité de vide complète

Polissage du verre au feu :Verre neuf

État du verre :factory condition

Diamètre:1 200 mm (47,2 po)

Longueur du côté droit :1 200 mm (47,2 po)

Type de support :Jambes

New equipment — in stock

UGE UA-500 — 1,900 L

New UGE UA-500 glass-lined reactor body. 1,900 L (500 gal) capacity with full vacuum capability and factory-new glass lining.

Capacité (conception) :Capacité de 1 900 L (500 gal).

Pression interne :6,9 bar (100 psi)

Température interne :232,2 °C (450 °F)

Vide interne complet :Capacité de vide complète

Polissage du verre au feu :Verre neuf

État du verre :factory condition

Diamètre:1 200 mm (47,2 po)

Longueur du côté droit :1,500 mm (59.1 in)

Type de support :Jambes

New equipment — in stock

Buy Reactor Bodies That Need Reglass

IPP stocks batch type body only reactor vessels in needs-reglass condition. These vessels have OEM-quality metal shells with glass linings that require replacement. IPP offers re-glassing services through its UGE division. Purchasing a needs-reglass vessel and re-glassing through UGE can provide the lowest total cost for a fully restored reactor body.

Needs Reglass Vessels Available

IPP stocks reactor bodies in needs-reglass condition from Pfaudler, DeDietrich, and EHW Thale. These vessels are priced at the lowest cost point and can be re-glassed through UGE to restore full glass-lining performance.

26 vessels in stock

Pfaudler, DeDietrich, EHW Thale

Re-glassing available through UGE

Lowest cost entry point

Need a Reactor Body? Ask an IPP Expert.

Tell us your capacity, pressure, and temperature requirements. Our team will match your specifications against current body only reactor inventory and provide a detailed quote.

Comparing Reactor Body Condition Options

IPP stocks body only reactor vessels across four primary conditions. Here is how re-glassed, new, used, and needs-reglass reactor bodies compare across key factors.

Facteur	Revêtu de verre	New (UGE)	Utilisé	Nécessite un remplacement de la vitrerie
Coût de l'équipement	Moderate — savings vs new OEM	Higher — factory-new glass	Lowest ready-to-use cost	Lowest vessel cost + reglass fee
Glass Lining Quality	Full Fire Polish, Very Clean	Factory-new glass	Varies — Some Fire Polish to Clean	Requires new glass lining
Délai de mise en œuvre	In stock — ready to ship	In stock — ready to ship	In stock — ready to ship	Requires re-glassing lead time
Unités en stock	61 vessels	27 vessels	46 vessels	26 vessels
Idéal pour	Replacement vessels needing clean glass	New installations requiring factory glass	Budget-conscious replacements	Lowest total cost with UGE re-glass
Fabricants	Pfaudler, DeDietrich	UGE (IPP subsidiary)	Pfaudler, DeDietrich, others	Pfaudler, DeDietrich, EHW Thale

Advantages of Buying Used Reactor Bodies from IPP

International Process Plants combines over 46 years of process equipment expertise, nearly 150 colleagues across 15 countries, and 172 body only reactor vessels in stock to deliver reactor shells ready for your process.

Des économies de coûts importantes

Buying used batch type body only reactors from IPP can save up to 50% of capital and 90% of lead time versus buying new. Body only vessels offer additional savings over complete reactor systems because the agitation system is excluded from the purchase.

Replacement Vessel Flexibility

Body only reactor vessels serve as direct replacement shells for existing reactor installations. Buyers can reuse their existing agitation system, drive assembly, and mechanical seal with a new or re-glassed vessel body.

Vitrage refait selon les spécifications d'usine

IPP offers re-glassed reactor bodies through its UGE (Universal Glasteel Equipment) division, founded in 1995, which stocks 700+ vessels and 2,700+ parts. 61 re-glassed bodies are in stock with full fire polish and very clean glass condition.

Top OEM Manufacturers in Stock

IPP stocks reactor bodies from Pfaudler, DeDietrich, UGE, EHW Thale, and Schwelm. Every unit is an original OEM product with traceable provenance. DeDietrich (France) and EHW Thale (Germany) represent European OEM manufacturing.

Présence mondiale dans 15 pays

IPP possède des bureaux dans 15 pays : Allemagne, Brésil, Canada, Chine, Espagne, États-Unis, France, Inde, Italie, Mexique, Pakistan, Portugal, République tchèque, Roumanie, Royaume-Uni et Turquie. IPP a servi plus de 160 000 clients dans le monde entier.

Full Range of Sizes & Specs

Volume capacity ranges from 15 L (4 gal) to 30,300 L (8,000 gal). Pressure ratings range from 0.14 bar (2 psi) to 20.7 bar (300 psi). Temperature ratings range from 40°C (104°F) to 343.3°C (650°F). Support types include legs, lugs, and ring. Bottom head types include dish, elliptical, flat (1 unit), and cone (1 unit).

Comment fonctionne l'achat d'un corps de réacteur d'occasion

Le processus d'achat d'un réacteur d'occasion auprès d'IPP comprend cinq étapes, de la spécification à la livraison.

1

Soumettre les exigences

Share your reactor body specifications: capacity, pressure rating, temperature, dimensions, and whether you need a replacement body for an existing system or a vessel for a new agitator.

2

Réception du paquet de données

IPP sends a detailed equipment data sheet with capacity, pressure rating, temperature, dimensions, nozzle schedule, glass condition report, and photographs of the vessel.

3

Verify Compatibility

The IPP team helps verify that the body dimensions, nozzle layout, and mounting configuration are compatible with your existing agitation system or planned installation.

4

Re-Glassing Options

IPP offers re-glassing through its UGE division (700+ vessels, 2,700+ parts in stock). Used or needs-reglass vessels can be fully restored before shipment.

5

Emballage et livraison

IPP prend en charge l'emballage, la mise en caisse, le transport et la livraison jusqu'à votre usine. Expédition internationale depuis nos bureaux situés dans 15 pays. Contactez IPP pour plus d'informations sur la livraison.

Industries That Buy Used Reactor Bodies

IPP supplies used batch type body only reactor vessels to manufacturers across multiple process industries worldwide.

Pharmaceutique

Traitement chimique

Biotechnologie

Restauration

Produits de beauté

Produits chimiques fins

produits agrochimiques

Polymères et résines

Peintures et revêtements

Produits pétrochimiques

Frequently Asked Questions About Purchasing Reactor Bodies

Answers to the most common questions from procurement and operations teams evaluating used batch type body only reactor vessels.

How many body only reactor vessels does IPP have in stock?

IPP stocks batch type body only reactor vessels. The largest manufacturer positions are Pfaudler, DeDietrich, and UGE. Volume capacity ranges from 15 L (4 gal) to 30,300 L (8,000 gal). Consultez l'inventaire IMS pour connaître la disponibilité actuelle.

What is a body only reactor?

A body only reactor is a reactor vessel shell sold without an agitation system. The vessel includes the reactor body, jacket, nozzles, manway, and support structure, but does not include an agitator, drive assembly, motor, or mechanical seal. Buyers typically purchase body only vessels as replacement shells for existing reactors, or to install their own agitation system.

How much can I save purchasing a used reactor body versus new?

Purchasing used batch type body only reactors from IPP can save up to 50% of capital and 90% of lead time versus buying new. The exact savings depend on manufacturer, capacity, and condition. IPP provides detailed quotes with full specification matching on request. Contact IPP for pricing on specific units from our current reactor body inventory.

What manufacturers of reactor bodies does IPP stock?

IPP stocks reactor bodies from 19 manufacturers. The largest inventory positions are Pfaudler, DeDietrich, UGE, EHW Thale, and Schwelm. Pfaudler, DeDietrich (France), and EHW Thale (Germany) represent major international glass-lined equipment manufacturers.

Does IPP sell new reactor bodies as well as used?

Oui. IPP stocks new glass-lined reactor bodies from its UGE (Universal Glasteel Equipment) subsidiary. UGE was founded in 1995 and provides glass-lined equipment through the IPP Group. IPP also stocks unused surplus reactor bodies — manufactured but never installed — offering new-equipment performance with immediate availability.

What condition grades are available for reactor bodies?

IPP stocks reactor bodies in five conditions: re-glassed, used, new from UGE, needs reglass, and unused surplus. Re-glassed reactor bodies have received new borosilicate glass linings through IPP's UGE division. Unused reactor bodies were manufactured but never installed in a process.

What does re-glassed mean for a reactor body?

Un réacteur remis à neuf a reçu un nouveau revêtement en verre borosilicaté sur le corps de la cuve d'origine. IPP propose des services de revitrage par le biais de sa division UGE (Universal Glasteel Equipment), fondée en 1995, qui dispose d'un stock de plus de 700 cuves et de plus de 2 700 pièces. Re-glassed bodies in IPP inventory show full fire polish (FF) and very clean (VC) glass condition ratings.

What glass condition grades does IPP report?

IPP reports glass condition grades on each reactor body listing. Grades include Very Clean (VC), Clean (C), Dirty (D) meaning light cleaning needed, and New for factory-new UGE vessels. Glass fire polish grades include Full Fire Polish (FF), Some Fire Polish (F), and New. These condition ratings help buyers assess glass lining quality before purchasing.

Quels matériaux de construction sont disponibles ?

IPP stocks body only reactor vessels primarily in glass-lined construction (166 of 172 units, or 96.5%). Additional units are available in stainless steel 316, stainless steel 316L (1 unit), stainless steel austenitic (1 unit), and Hastelloy (1 unit). Sa construction à revêtement en verre offre une résistance à la corrosion pour les procédés de fabrication pharmaceutiques, chimiques et spécialisés.

Can you buy a reactor body and add your own agitation system?

Oui. Body only reactor vessels are sold without an agitation system. Each vessel listing includes a nozzle schedule that specifies the drive nozzle size and location for mounting an agitator. For example, IPP# 246494 (UGE UA-300) specifies a 4 3/8” agitator nozzle. Buyers can mount their own agitator, reuse an existing drive assembly, or source a new agitation system to fit the vessel nozzle configuration.

Are Pfaudler reactor bodies compatible with other manufacturers' agitators?

Pfaudler reactor bodies include drive nozzles with standardized dimensions listed in the nozzle schedule. Compatibility with other manufacturers' agitators depends on matching the drive nozzle diameter, flange pattern, and vessel geometry. The IPP team can help verify compatibility for specific body and agitator combinations. Contact IPP with your existing agitator specifications for a compatibility assessment.

Can IPP supply both a reactor body and a separate agitation system?

IPP's Gale Process Solutions (GPS) subsidiary provides custom fabricated equipment. Contact IPP to discuss sourcing a matched reactor body and agitation system together.

What nozzle configurations are available on body only vessels?

Each reactor body listing in IPP inventory includes a detailed nozzle schedule specifying the number, size, and location of all vessel openings. Typical nozzle schedules include manway openings (12” to 18”), process nozzles (2” to 10”), drive nozzles (4 3/8”), and bottom outlet nozzles. Contact IPP with your required nozzle configuration for specific recommendations.

What support types are available for reactor bodies?

IPP stocks reactor bodies with three support types: legs, lugs, and ring supports. The support type determines how the vessel is mounted in your plant. Leg-supported vessels stand on the floor, while lug-supported vessels are mounted from above on structural steel. Contact IPP to find reactor bodies matching your plant's mounting configuration.

Looking for Complete Agitated Reactors?

IPP also stocks batch-type agitated reactors — complete reactor systems with agitation, drive assembly, motor, and mechanical seal included. IPP offers used and glass-lined process equipment through UGE, and new stainless steel and alloy equipment through GPS, available as both stocked and custom-fabricated solutions.

Ready to Buy a Reactor Body?

Depuis 1980, IPP fournit des équipements de process de qualité dans le monde entier et compte plus de 160 000 clients. Faites-nous part de vos besoins : notre équipe vous proposera les produits et les prix adaptés.